![]() Well it is because it worked all fine until today. It says that QLink is either not working properly or is not installed. I'm by no way savvy to manage this alone. I noticed that it had quite a lot of HD activity after the boot. I can't see find it in my router list and it is still not visible in my data browser (Finder). the long beep at the end of the booting process. I have rebooted the NAS about an hour ago and it booted like usually w. Today I can't see the symbols in my finder's left side fav. I can't exactly recall what kind of connection I've been using but as far as I remember I had configured SAMBA and the other windows option which I can't recall the name. Make sure the NAS and the computer that runs QNAP Qfinder are connected to the same subnet. I usually see it and access it via my Mac's finder. If the NAS has been configured to use DHCP, you can use QNAP Qfinder to check the IP address of the NAS. It has been working fine since over a year but today. So the TS-431 isn't as crippled as I once thought it was.Hi everybody, I can't reach TS 431 over my local network since today. ![]() With an intermediate inode size of 16384, it showed a maximum volume size of 64TB. With a 65536 byte inode size, it says that the maximum volume size is 144TB. With 4096 bytes, you get maximum number of files on the NAS, but a max total volume size of 16TB. With the 4.2.2 firmware, I was given an option of "inode size", when creating the filesystem, with options ranging from 4096 bytes, to 65536 bytes. The TS-431 was noted by others, as having a limit to the RAID array volume size, of 16TB. QNAP Qfinder Pro allows you to find and access the Turbo NAS over the LAN. Turns out, the Network Config was wrong, it defaulted to a subnet mask of "255.255.0.0", rather than "255.255.255.0" (the correct one for my small LAN).Įdit: Another note, while I'm committing this to Google for posterity. QNAP TS453D Disk Tray They do not have stock for the 4TB hard drives and. QNAP TS-431P2-1G All in One Turbo NAS Kayt Cihaz en iyi fiyatla. But not under Computer, where you double-click to access the shares. To locate the NAS, you can: a) Install the Qfinder Pro utility, b) Scan the QR code. You could double-click on it under Storage, and it would open the admin web page. In both Windows 7 and Windows 10, the NAS was NOT showing up under the "Computer" section, but it WAS showing up under the "Media" and "Storage" sections. It's been around 12 hours, and it's 75% complete.īut I had another problem. This time, it succeeded, and was doing the RAID-5 re-build in the background as a Background Task. ![]() I was then able to finally get back into the web interface, and then login with the admin credentials that I set up during the quick setup, and manually re-do the RAID-5, and format the drives. ![]() Then finally, after a reboot, it was showing 4.2.2 firmware, rather than 4.2.1. The NAS seems to be booted, and when I turn off the. The message below comes up through Qfinder Pro, I'm not sure how to action other than I've checked and it appears that both the NAS and deco and computer are all on the same subnet. Which, according to QFinder, quit part-way through, but the NAS status light at that point was blinking green and red, so I figured, I'd let it finish. Qfinder Pro no longer finds the NAS and the mapped network drives don't work and time machine hasn't backed up. It caused the NAS itself to go out and download the firmware (it was connected to LAN and internet), and then it started installing the firmware itself. So then I tried again, there was an option to simply "Auto-update to latest firmware", which I chose. So I tried downloading the firmware, unzipping it on my PC, and uploading it using QFinder to the NAS. It showed the TS-431 with a "RED X" mark, along with a green arrow (needs firmware update). So I downloaded QNAP Finder software ("QFinder"), and it saw my NAS units on my LAN (I have several QNAPs). Seems like there's an issue using drives that have previously been in some kind of server, stopping the format routine? Anyways, I shut it down, started it up, pulled each drive (while on), got a RED status light, plugged each drive back in in sequence, still had the RED status light (didn't auto-recover). QVR Elite is the subscription-based network video recorder software for QNAPs QTS, QuTS hero, and QNE Network operating systems. If the hard drives in your QNAP NAS are not fully compatible, issues such as. I opted for a "Bad Block Scan", which took like 12 hours, and then it went to "Formatting: 64%", and stuck there for like another 24 hours. I have too a recently bought QNAP TS-431P and it have 2x Ethernet ports. I loaded 4x2TB 5400RPM Hitachi CoolSpin 5K3000 HDDs into it, and booted it, and it went into the EZ Quick Setup procedure. I recently set up a brand-new QNAP TS-431 4-bay NAS.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |